Attachment 4615 Details for Bug 26058

Documentation v2

networking.markdown (text/plain), 11.22 KB, created by Philipp Hahn on 2012-08-23 12:20 CEST

(hide)

Description:

Filename:

MIME Type:

Creator: Philipp Hahn

Created: 2012-08-23 12:20 CEST

Size: 11.22 KB

patch

obsolete

>Advanced networking configuration
>=================================
>
>UCS-3.1 supports advanced network configurations using bridging, bonding and
>virtual networks (VLAN).
>
>* Bridging is often used with virtualization to connect multiple virtual
>  machines running on a host through one shared physical network interface.
>
>* Bondings allows fail-over when a host has multiple physical network
>  interfaces to the same network.
>
>* VLANs can be used to separate network traffic logically while using only one
>  (or more) physical network interface.
>
>Configuration happens through setting several UCR variables to construct a
>valid configuration.  Currently no wizard exists for graphical configuration
>and each setup is explained by one example, which must be adopted to the
>required setup.
>
>
>Bridging
>--------
>
>Bridging allows a physical network interface to be shared by multiple virtual
>machines running on a single host.  Instead of using one physical interface for
>each virtual machine and the host itself, all hosts are connected through only
>one (or more) uplink, which is then split up virtually just like a physical hub
>or switch would do.  Bridges must never form a loop, where multiple paths
>exists from one source host to a destination host.  This is managed by the
>Spanning Tree Protocol (STP), which Linux only supports natively in the older
>not-*rapid* version.  If bridging is used for virtual machines and the host is
>a leaf node (that is the bridge does not really connect two physical network
>interfaces and is not supposed to forward traffic between those networks), STP
>should be disables and the so called *forwarding* delay should be set to 0 to
>allow virtual machines to be booted from the network by PXE.
>
>### Prerequisite ###
>
>* The *bridge-utils* package must be installed:
>
>        univention-install bridge-utils
>
>* The *bridge* kernel module must be loaded:
>
>        modprobe bridge
>        ucr set kernel/modules="$(ucr get kernel/modules);bridge"
>
>* Make sure to never build a network loop using bridges!
>
>### Setup ###
>
>* This example uses two physical interfaces (eth0, eth1), but for virtual
>  machines using only one physical interface is perfectly fine.
>
>* The physical network interfaces must not have IP addresses configured and
>  must not be started automatically.
>
>* Instead the bridge device (br0) gets the IP address and is used as the
>  primary interface for all services on the host itself.
>
>* The forwarding delay of the bridge is set to 0, which instantly puts the
>  bridge in forwarding mode when new links are connected to the virtual bridge.
>  This is needed for virtual machines to boot from the network via PXE, because
>  otherwise the initial DHCP packets will not reach the network.
>
>### Configuration ###
>
>    xargs ucr set <<__BRIDGE__
>    interfaces/eth0/type=manual
>    interfaces/eth0/start=false
>    interfaces/eth1/type=manual
>    interfaces/eth1/start=false
>    interfaces/br0/address=192.168.122.13
>    interfaces/br0/broadcast=192.168.122.255
>    interfaces/br0/netmask=255.255.255.0
>    interfaces/br0/network=192.168.122.0
>    interfaces/br0/options/1="bridge_ports eth0 eth1"
>    interfaces/br0/options/2="bridge_fd 0"
>    interfaces/br0/start=true
>    interfaces/primary=br0
>    __BRIDGE__
>
>
>Bonding
>-------
>
>Bonding allows two (or more) physical network interfaces to be aggregated or to
>be used in fail-over scenarios.  Different modes are supported by the
>bonding driver, but this example configures a active-passive fail-over
>scenario.
>
>### Prerequisite ###
>
>* The *ifenslave-2.6* package must be installed:
>
>        univention-install ifenslave-2.6
>
>* The *bonding* kernel module must be loaded:
>
>        modprobe bonding
>        ucr set kernel/modules="$(ucr get kernel/modules);bonding"
>
>* Active-passive setups can be configured with any switch, while active-active
>  setups and channel aggregation must be supported by the switch.
>
>### Setup ###
>
>* The physical network interfaces (eth0, eth1) must not have IP addresses
>  configured and must not be started automatically.
>
>* Instead the bonding device (bond0) gets the IP address and is used as the
>  primary interface for all services on the host itself.
>
>* The bonding is configured to check the link state of the physical interfaces
>  all 100 ms using the hardwares MMI monitor.
>
>* In case of a link failure the hosts switches the active link over to the
>  other interface and stays there until that link fails too.
>
>### Configuration ###
>
>    xargs ucr set <<__BONDING__
>    interfaces/eth0/type=manual
>    interfaces/eth0/start=false
>    interfaces/eth1/type=manual
>    interfaces/eth1/start=false
>    interfaces/bond0/address=192.168.122.13
>    interfaces/bond0/broadcast=192.168.122.255
>    interfaces/bond0/netmask=255.255.255.0
>    interfaces/bond0/network=192.168.122.0
>    interfaces/bond0/options/1="bond-slaves eth0 eth1"
>    interfaces/bond0/options/2="bond-mode 1"
>    interfaces/bond0/options/3="mmimon 100"
>    interfaces/bond0/options/4="bond-primary eth0 eth1"
>    interfaces/bond0/start=true
>    interfaces/primary=bond0
>    __BONDING__
>
>
>### Virtual LANs ###
>
>VLANs can be used to separate network traffic by using different networks
>(think broadcast-domain).  Instead of using multiple physically separated
>networks, the network packets are tagged with a VLAN-ID, which must be
>configured on all switches.  A linkt between two switches can either transport
>only (untagged) packets of a single VLAN, or can transport packets of multiple
>VLANs; the later case calls this a *trunk*-link.  The switches are responsible
>for for adding and removing the tags when forwarding between trunk links and
>links dedicated to only one VLAN.
>
>Servers are some times connected to multiple VLANs as well: In this case they
>are connected though trunk links as well and multiple virtual interfaces must
>be configured on the host, each one with its own IP address.
>
>### Prerequisite ###
>
>* The *vlan* package must be installed:
>
>        univention-install vlan
>
>* The *8021q* kernel module must be loaded:
>
>        modprobe 8021q
>        ucr set kernel/modules="$(ucr get kernel/modules);8021q"
>
>* Switches must support 802.1q VLANs.
>
>### Setup ###
>
>* eth0 is a trunk link, which carries tagged packages of VLAN 2 and VLAN 3.
>
>* eth0 itself receives no IP address, only the untagged virtual interfaces
>  eth0.2 and eth0.3.
>
>* eth0.2 is used as the primary interface for all host related services.
>
>### Configuration ###
>
>    xargs ucr set <<__VLAN__
>    interfaces/eth0/type=manual
>    interfaces/eth0/start=false
>    interfaces/eth0.2/address=192.168.122.13
>    interfaces/eth0.2/broadcast=192.168.122.255
>    interfaces/eth0.2/netmask=255.255.255.0
>    interfaces/eth0.2/network=192.168.122.0
>    interfaces/eth0.2/start=true
>    interfaces/eth0.3/address=10.200.17.1
>    interfaces/eth0.3/broadcast=10.200.17.255
>    interfaces/eth0.3/netmask=255.255.255.0
>    interfaces/eth0.3/network=10.200.17.0
>    interfaces/eth0.3/start=true
>    interfaces/primary=eth0.2
>    __VLAN__
>
>
>All together
>------------
>
>Bonding, bridging and VLANs can be combined to implement very flexible
>networks.  In this example the host has three physical network interfaces.  One
>interface (eth2) is dedicated to the host itself, while the two other
>interfaces (eth0, eth1) are configured for high availability by using bonding.
>To support virtual machines in different virtual networks, VLANs 2 and 3 are
>used to separate network traffic.  For each VLAN a separate bridge is created,
>so virtual machines only see their traffic and cannot use the VLAN tools
>themselves to get access to different VLANs.
>
>
>### Prerequisite ###
>
>* The *ifenslave-2.6*, *bridge-utils* and *vlan* packages must be installed:
>
>        univention-install ifenslave-2.6 bridge-utils vlan
>
>* The *bonding*, *bridge*, and *8021q* kernel modules must be loaded:
>
>        modprobe bonding
>        modprobe bridge
>        modprobe 8021q
>        ucr set kernel/modules="$(ucr get kernel/modules);bonding;bridge;8021q"
>
>* Switches must support 802.1q VLANs.
>
>### Setup ###
>
>* The order in the generated /etc/network/interfaces files is very important,
>  which is why the order is explicitly specified in this example.  Otherwise
>  the interfaces would be sorted by their names, which is not sufficient in
>  this complex setup.
>
>* eth0 and eth1 are trunk links, which carry tagged packages of VLAN 2 and
>  VLAN 3.
>
>* They are bound together for fail over by building a bonding device bond0,
>  which must be explicitly started.
>
>* VLAN 2 and VLAN 3 are configured on the host and are provided untagged on the
>  bond0.2 and bond0.3 devices.
>
>* For each VLAN a dedicate bridge br2 and br3 is created, which only has access
>  to that one VLAN.  Virtual machines should be connected to those bridges.
>
>* The host itself used the dedicated eth2 interface, which is configured
>  normally.
>
>### Configuration ###
>
>    xargs ucr set <<__VM__
>    interfaces/eth0/order=2
>    interfaces/eth0/type=manual
>    interfaces/eth0/start=false
>    interfaces/eth1/order=2
>    interfaces/eth1/type=manual
>    interfaces/eth1/start=false
>    interfaces/bond0/order=3
>    interfaces/bond0/type=manual
>    interfaces/bond0/options/1="bond-slaves eth0 eth1"
>    interfaces/bond0/options/2="bond-mode 1"
>    interfaces/bond0/options/3="mmimon 100"
>    interfaces/bond0/options/4="bond-primary eth0 eth1"
>    interfaces/bond0/start=true
>    interfaces/bond0.2/order=4
>    interfaces/bond0.2/type=manual
>    interfaces/bond0.2/start=false
>    interfaces/bond0.3/order=4
>    interfaces/bond0.3/type=manual
>    interfaces/bond0.3/start=false
>    interfaces/br2/order=5
>    interfaces/br2/type=manual
>    interfaces/br2/options/1="bridge_ports bond0.2"
>    interfaces/br2/options/2="bridge_fd 0"
>    interfaces/br2/start=true
>    interfaces/br3/order=5
>    interfaces/br3/type=manual
>    interfaces/br3/options/1="bridge_ports bond0.3"
>    interfaces/br3/options/2="bridge_fd 0"
>    interfaces/br3/start=true
>    interfaces/eth2/order=1
>    interfaces/eth2/address=192.168.122.13
>    interfaces/eth2/broadcast=192.168.122.255
>    interfaces/eth2/netmask=255.255.255.0
>    interfaces/eth2/network=192.168.122.0
>    interfaces/eth2/start=true
>    interfaces/primary=eth2
>    __VM__
>
>
>Trouble shooting
>----------------
>
>* Changing the network configuration on a running system is dangerous, since
>  any misconfiguration can make the host unreachable.  Make sure to have an
>  out-of-band access path to a root shell!
>
>* The name of an interface depends on the loading order of kernel modules and
>  on the timing the hardware needs to reach a ready state.  *udev* tries to assign
>  persistent names to the interfaces using their MAC address, which is stored
>  in */etc/udev/rules.d/70-persistent-net.rules*.  If interfaces get removed or
>  replaced by other interfaces with a different MAC address, old named won't
>  get reused until that file is reset.
>
>* UVMM normally uses eth0 to configure the bridge to connect virtual machines
>  to a network.  This was archived by renaming the physical interface eth0 to
>  peth0 and creating a bridge called eth0, into which the physical interface
>  was connected.  This is no longer recommended and automatic support for this
>  will be removed in future versions of UCS.
>
>  You can and should deactivate the scrips by setting the following UCR variables:
>
>        xargs ucr set <<__UVMM__
>        uvmm/kvm/bridge/autostart=no
>        uvmm/kvm/bridge/interface=
>        xen/bridge/interface=none
>        __UVMM__

Actions: View

Attachments on bug 26058: 4157 | 4611 | 4615